PDA

View Full Version : Lee BIG Stopper



Xenedis
31-07-2010, 3:43pm
Has anyone been able to land a Lee BIG Stopper (http://www.leefilters.com/camera/products/show/ref:C4B8F834D908E7/) (ten-stop ND filter)?

If so, where did you find one?

My usual supplier of Lee filters seems to be permanently out of stock.

Are these very difficult to obtain at the moment?

Paul G
31-07-2010, 4:09pm
Seems to have been a few people chasing them recently. Arnica (Phil) picked up a B+W 10 stop instead back in June.
Just wondering though does the extra stop make much difference from a ND400 (9 stops)?

http://www.ausphotography.net.au/forum/showthread.php?t=59983

peterb666
31-07-2010, 5:32pm
I have been using a HiTech 8 stop (2.4) filter. They make to 10-stop and a reasonably priced (well compared to Lee and B+W).

HiTech are claimed to be colour neutral but I don't agree with that. In some lighting conditions they do display the dreaded purple colour cast that stacked Cokin filters and others are known to exhibit. Still you can generally tame it post-processing.

If you already own a 9-stop filter, I would think you would be wasting your money to go an extra stop.

Xenedis
31-07-2010, 5:41pm
I don't own a nine-stop filter; I have one three-stop screw-in filter and two three-stop Lee resin filters.

ricktas
31-07-2010, 6:18pm
Ive got one : www.vanbar.com.au

peterb666
31-07-2010, 6:19pm
Sorry x-man

I was really replying to goodallphotography - I guess I should have quoted.

I know you don't have a 9-stopper.

Xenedis
31-07-2010, 7:41pm
Ive got one : www.vanbar.com.au

Thanks for that.

The problem I found with Vanbar is that it's significantly more expensive than my overseas supplier, even with currency conversion rates.

When I bought my first Lee kit (0.9 GND, 0.6 GND, holder and lens adapter), Vanbar wanted $200 more than my overseas supplier.

Studio Kit Direct is asking £80 for the Lee BIG Stopper, which translates to around $AUD 140.

With Vanbar does the ability to add an item to the cart in the online shop indicate that the item is available?

peterb666
31-07-2010, 8:38pm
With Vanbar does the ability to add an item to the cart in the online shop indicate that the item is available?

I don't know. They do all their mail order from Melbourne.

When I did my shopping with them, I rang the Sydney store, they checked the stock and location. One item was out of stock in Sydney but available from Melbourne so I was given the choice of mail order including the shipping cost or order from Sydney and pick up for free. I did the latter.

When the supplier was a little tardy, they said they would get the item up from Melbourne at no additional cost it it didn't arrive in a day or two, but then the item came in anyway.

peterb666
31-07-2010, 8:50pm
Mediavision in Gladesville are the other Australian seller of Lee.

No website but this posting in another forum indicates that Medavision were selling them for $160.

http://www.photoforum.com.au/showthread.php?38176-82mm-ND10-Filter

Phone number of Mediavision is (02) 9816 4055 and the address is 4 Monash Rd, Gladesville

Hope this may help.

Cheers

Peter

dulvariprestige
31-07-2010, 9:25pm
10 stop B+W ND here for a $167.80 delivered
http://cgi.ebay.com.au/B-W-77mm-110-ND-1000X-Filter-NEW-F-PRO-/280538540822?cmd=ViewItem&pt=AU_Cameras_Photographic_Accessories&hash=item4151666b16

bigjobs
01-08-2010, 8:50am
Thanks for that.
With Vanbar does the ability to add an item to the cart in the online shop indicate that the item is available?

No it doesn't, I found that out recently... best to call first.

I recently picked up some Lee stuff from Vanbar about a month ago but almost everything was back-ordered. I spoke to them about it and apparently most of the stock they had coming in was already allocated to orders.

Some sort of world-wide shortage I was told. They did have some Big Stoppers available when the stock did arrive though - I did consider buying one.

ricktas
01-08-2010, 8:57am
No it doesn't, I found that out recently... best to call first.

I recently picked up some Lee stuff from Vanbar about a month ago but almost everything was back-ordered. I spoke to them about it and apparently most of the stock they had coming in was already allocated to orders.

Some sort of world-wide shortage I was told. They did have some Big Stoppers available when the stock did arrive though - I did consider buying one.

I ordered my big stopper on a Sunday night from Vanbar, it arrived on Tuesday.

peterb666
01-08-2010, 2:10pm
The other UK supplier is Teamwork Photo & Digital. They are also GBP80 and out of stock but are taking orders with a 6 to 8 week lead time for supply.

Teamwork Photo (http://www.teamworkphoto.com/index.php?main_page=product_info&cPath=78_769_300&products_id=14764)

They also carry HiTech who do filters to 10-stop but note the HiTech 8-stopper I have DOES exhibit a colour cast under some lighting conditions.

Wayne
01-08-2010, 6:45pm
Buy here http://cgi.ebay.com/B-W-77mm-ND-3-0-1000X-110-NEUTRAL-DENSITY-Filter-77-/360274724594?cmd=ViewItem&pt=Camera_Filters&hash=item53e20c06f2#ht_4599wt_1136

I have bought several genuine B+W filters from them, all arrive quickly and always cheaper than Mainline.

Xenedis
01-08-2010, 7:14pm
Buy here http://cgi.ebay.com/B-W-77mm-ND-3-0-1000X-110-NEUTRAL-DENSITY-Filter-77-/360274724594?cmd=ViewItem&pt=Camera_Filters&hash=item53e20c06f2#ht_4599wt_1136

The Lee BIG Stopper is a 100mm x 100mm filter for creative systems.

The filter you've linked is a screw-in type (which is the wrong size for my 82mm-diameter lens).

I need the sheet filter type for my Lee system.

Analog6
01-08-2010, 7:49pm
The dealers for Lee in Australia are:

Vanbar Imaging
159 Cardigan Street,
Carlton,
Victoria 3053,
Australia
Tel: 03 9347 7788
Fax: 03 9347 0407
Email: lee@vanbar.com.au
Website: http://www.vanbar.com.au

and
Mediavision Australia
4 Monash Road,
Gladesville,
N.S.W 2111,
Australia
Tel: 00 612 9816 4055
Email: sales@mediavision.com.au

I have used Teamwork Digital (UK) and Vanbar for my Lee purchases

bb45pz
01-08-2010, 8:27pm
I've got three questions along these lines.
Does the big stopper truly have a zero colour cast?

Does it fit in a Hitech 100mm holder?

and where can you get the Hitech 2.4 that Peter mentioned? I looked on the Formatt website but they don't seem to list it.

Thanks...

peterb666
01-08-2010, 8:48pm
and where can you get the Hitech 2.4 that Peter mentioned? I looked on the Formatt website but they don't seem to list it.

Thanks...

This page from the first drop down list box. http://www.formatt.co.uk/stills-filters/filters/standard-n-d/stills-filters.aspx

It is a "High density" filter

ricktas
01-08-2010, 8:55pm
I've got three questions along these lines.
Does the big stopper truly have a zero colour cast?

Does it fit in a Hitech 100mm holder?

and where can you get the Hitech 2.4 that Peter mentioned? I looked on the Formatt website but they don't seem to list it.

Thanks...


I use mine with the Cokin Z-Pro system, as long as you have a 100mm filter system it should fit! It comes with spongey material stuck to the edges to cut light leak in around the sides of the filter and holder.

I got an interesting purple cast from one photo out of a set I took recently. BUT as I and a few others alluded to quite some time ago in a thread, we think the colour cast issue is a white balance one. That the cameras are reading the white balance incorrectly when ND filters are in place. I have seen it corrected by a simple white balance adjustment in RAW conversion. The purple cast is not seen all the time, even with the Cokin filters, if the filter was the cause, it should be. We surmised that under certain light conditions the camera reads a faulty white balance and the purple cast is not caused by the filter as such, but the camera in combination with ND filters and certain light conditions.

bb45pz
01-08-2010, 10:07pm
Thanks Rick and Peter,

I noticed on the formatt site theres a '3' option as well as the 2.4 so perhaps thats their 10 stopper. If so I'll stick with the Hitech as I've basically just kitted myself out with Hitech filters.

peterb666
01-08-2010, 10:22pm
That's the 10-stopper. Each 0.3 is one stop.

bb45pz
01-08-2010, 10:42pm
Nice, that ones on the way then :)

Regnis
02-08-2010, 3:09pm
I was wondering if anyone has had any experience with the Hitech filter holder (100mm).

I am desperately trying to get a system before i go to the states on tuesday next week. (or during my first week in the states)

The Lee system is a little out of my budget so I was just looking to pick up the Lee holder and adapter 77mm... but even the prices on these are quite steep. I was quoted $103 for the holder and $68 for the wide angle holder.

So I am now pretty keen on getting the Hitech holder and adapter but would just like to know if I will get vignetting at 10mm? (to order hitech I would have to get it sent to the states and pick it up while i'm there.)

Not sure what to do:confused013

falke
13-02-2011, 2:55pm
I use mine with the Cokin Z-Pro system, as long as you have a 100mm filter system it should fit! It comes with spongey material stuck to the edges to cut light leak in around the sides of the filter and holder.

I got an interesting purple cast from one photo out of a set I took recently. BUT as I and a few others alluded to quite some time ago in a thread, we think the colour cast issue is a white balance one. That the cameras are reading the white balance incorrectly when ND filters are in place. I have seen it corrected by a simple white balance adjustment in RAW conversion. The purple cast is not seen all the time, even with the Cokin filters, if the filter was the cause, it should be. We surmised that under certain light conditions the camera reads a faulty white balance and the purple cast is not caused by the filter as such, but the camera in combination with ND filters and certain light conditions.

I assume Xenedis has been lucky in purchasing that filter by now (to get back to the original question).

Rick I just like to say that I was not as lucky as you with matching the big stopper with a Cokin Z pro system (there is a specific thread on that). The spongy material does not match up with the frame of the Z pro frame I used to own, to the effect that there is light leakage that rendered my shots useless.

With regard to the colour cast (I now successfully use the Lee system), I can confirm that it is a white balance issue. I shoot in RAW and my shots can easily be adjusted by just changing the white balance.

I have however another difficulty to do with strong vignetting. Here is an example of a shot I took this morning with my Pentax K-x and a Sigma 10-20 (4.5 to 5.6) lens:
http://i1037.photobucket.com/albums/a456/Kronau1/_IGP6660.jpg
Could this be a result of the combination of lens and filter? I use wide angle adapters with my Lee filter holder. This shot had the white balance adjusted and was straightened a little - all in ACR.

(Ps this is my first reply with a photo link - I hope I did it correctly)

peterb666
13-02-2011, 6:00pm
That vignetting is not due to intrusion from the edge of the filter or holder. You will always have a vignetting with ultra-wide lenses as the angle of light going through the filter is at a greater angle to perpendicular the more you move away from the centre. Basically you are putting a flat piece of glass or plastic over a lens that gathers light at varying angles. The light moves through more glass/plastic near the edges and also more ND tinting.

If you are shooting RAW, you can remove it with the vignetting control in your RAW processing software.

falke
13-02-2011, 10:06pm
That vignetting is not due to intrusion from the edge of the filter or holder. You will always have a vignetting with ultra-wide lenses as the angle of light going through the filter is at a greater angle to perpendicular the more you move away from the centre. Basically you are putting a flat piece of glass or plastic over a lens that gathers light at varying angles. The light moves through more glass/plastic near the edges and also more ND tinting.

If you are shooting RAW, you can remove it with the vignetting control in your RAW processing software.

Yep Peter I totally agree. The light would move through (insert mathematical formula here) = thickness at about 45 degree angle. (assuming a viewing angle of 90 degree with the 10mm setting on the above lens)

Now I would like to take this discussion further in asking how this affect would be in taking a similar shot with a 17mm lens on a FF camera. My guess would be that, albeit achieving a similar wide angle effect and outcome, the vignetting would not be as strong (similar to distortions) at 17mm on a FF as compared to 10mm on a crop sensor camera. Is that right?

ps, since I am using the Lee filter holder I am not having any problems with light intrusions anymore.

Thanks

peterb666
13-02-2011, 11:33pm
Well 10mm on a 1.5 crop sensor is 15mm equivalence and while there is some difference, I would expect some issues with with a 17mm full-frame lens as well.

I cannot comment about light spill around the edges affecting the image. I am still making use of P-series holders and I know even the P-series wide angle holder with the 10-24mm Nikon lens is marginal (e.g. I cannot angle the filter for a sloping horizon without vignetting from the holder).

I have a love-hate relationship with my 8-stopper and prefer to use a 4-stopper if I can. It is just too difficult to predict the outcome in different ligting and the effects range from exellent to crap and everything in-between.

I will eventually be going to Z-pro, but for the time being I will be sticking with what I have. The cost of re-filtering to Z-Pro would be close enough to the cost of a macro lens which I need more. I can always shoot to around 14mm (21mm equivalent) with a standard P-series holder or use my 9-18mm MFT lens on my Olympus to give me a 18mm ff equivalent. There will always be times when I do want to stack either a 3 or 4-stop ND and a 3-stop GND but will probably wind up going for the HiTech filter holder when upgrading.

BTW, I have just cancelled an order for a Z-Pro holder and filter kit that had been outstanding for around 12 weeks. I have learnt to live with the P-series.

peterb666
06-10-2011, 10:36pm
I placed a mini-review of the new HiTech Pro 10-stopper on my blog site...

Mini Review of Hitech Pro 10-stop filter (http://peterbphotos.blogspot.com/2011/10/mini-review-of-hitech-pro-10-stop.html)

It seems to perform quite well. Not a trace of the magenta tint that was strong in some ligthing situations (and absent in others) with my old 8-stopper, but instead a vert modest and easily correctable green tint similar to that from the Lee 10-stopper.

At a cost of around $100 including shipping, this is a good value product that performs well.

http://farm7.static.flickr.com/6226/6216468223_deea4a51ff_z.jpg (http://www.flickr.com/photos/23034038@N05/6216468223/)
Sorrento Front Beach 2 (HiTech 10-stopper) (http://www.flickr.com/photos/23034038@N05/6216468223/) by peterb666 (http://www.flickr.com/people/23034038@N05/), on Flickr

It is also available for immediate shipping from either HiTech (Format Filters) or Teamworks in the UK. Order one and you will have it in about 1 week.

psyfre
01-11-2011, 7:39pm
Anyone got an underground black market Lee Filter vendor who could pass on a Big Stopper? The 4 month wait is killin' me!

Bennymiata
02-11-2011, 11:32am
I read an article somewhere about using the glass out of a welder's mask as a very strong ND filter.
They're cheap and might be worth a go in case of emergency.

Personally, I have a variable ND filter (a Sing-Ray) that goes from 2 stops to about 8 stops.
It could also be used, in a pinch, with additional ND filters to give you an even stronger effect.

dulvariprestige
02-11-2011, 12:27pm
Benny have you been able to see how many stops you can get out of your vari ND On an UWA yet.

psyfre
02-11-2011, 2:06pm
I actually had a go with the welders glass ND last year, neat trick but not very practical.

The glass I got was 17 stops in total! Here were the results:

http://fc05.deviantart.net/fs70/f/2010/286/1/e/1e4966569bdb203413e1094ebefab5aa-d2lwuc0.jpg

http://fc00.deviantart.net/fs71/f/2010/078/3/b/3bd24b1a2d5058c6173d8fd1c0b1911e.jpg

Bennymiata
02-11-2011, 3:41pm
Benny have you been able to see how many stops you can get out of your vari ND On an UWA yet.

Hard to say exactly, but is around 6 stops using a Tokina 11-16mm at 11mm.
If I turn it more when the lens is set to its widest, I do get some vignetting of the corners, but if I zoom it up to around 14mm, then I can go to the darkest setting which is around 8 stops.

Thoise shots using the welder's glass, pysfre, are not too bad and if you didn't tell anyone you used it, they would never know.
Cheap way to get a big ND filter!
Trouble is I guess they're hard to fit. Did you tape it on the front of the lens?

peterb666
02-11-2011, 5:02pm
I actually had a go with the welders glass ND last year, neat trick but not very practical.

The glass I got was 17 stops in total! Here were the results:

http://fc05.deviantart.net/fs70/f/2010/286/1/e/1e4966569bdb203413e1094ebefab5aa-d2lwuc0.jpg

http://fc00.deviantart.net/fs71/f/2010/078/3/b/3bd24b1a2d5058c6173d8fd1c0b1911e.jpg

Amazing. Welders glass is far from neutral so how you managed to get that sort of colour out of it is quite an achievement.

Sent from my GT-I9100 using Tapatalk

psyfre
03-11-2011, 7:49am
Cheers Benny, I bought a empty filter ring for my lens and glued the glass onto it. Thanks Peter, I set a custom white balance with the glass on then did the rest in PP :)

Xenedis
15-01-2012, 6:15pm
It looks like the Lee BIG Stopper is still difficult if not impossible to obtain.

I'll probably order the Hitech Pro Stop (http://www.formatt.co.uk/stills-filters/filters/standard-n-d/pro-stop.aspx) 10-stop filter instead.

GrahamS
15-01-2012, 6:30pm
Hey mate.
I too was trying to get the Big Stopper here or overseas. After nearly giving up on the idea, Fleabay had one, paid more than I should have but the money is worth it. Takes a bit of maths to get it figured, but as i say........worth it.
Good luck with whatever you do mate.
Cheers.

arthurking83
15-01-2012, 6:52pm
Amazing. Welders glass is far from neutral so how you managed to get that sort of colour out of it is quite an achievement.

....

As long as the colour cast is even across the entire frame, a click to WB value isn't hard to do to get a 'correct' colour balance.
It's when you use stacked GNDs and get a colour cast in only half the frame is where you run into issues that require major and complicated steps.

The real question tho is, how does the very basic quality of a welders glass piece stack up against optical quality filters.

Xenedis
15-01-2012, 7:07pm
Takes a bit of maths to get it figured

Not if you have my ND filter shutter speed cheat sheet (http://xenedis.wordpress.com/2011/07/20/nd-filter-shutter-speed-cheat-sheet/). :-)

I've just checked that, and unfortunately I only wrote it to handles six stops (the maximum light reduction hitherto available to me). I might update it to include the full ten stops.


Good luck with whatever you do mate.

I ordered the Hitech filter tonight.

peterb666
15-01-2012, 10:48pm
The HiTech Pro 10-stopper comes with it's own cheat sheet that fits perfectly in the window on the front of the Lee 10-filter case.

Xenedis
15-01-2012, 11:04pm
The HiTech Pro 10-stopper comes with it's own cheat sheet that fits perfectly in the window on the front of the Lee 10-filter case.

Handy to know; thanks.

I'll see if it suits my needs, and if not, I'll update my chart.

enduro
23-01-2012, 10:28pm
I use mine with the Cokin Z-Pro system, as long as you have a 100mm filter system it should fit! It comes with spongey material stuck to the edges to cut light leak in around the sides of the filter and holder.

I got an interesting purple cast from one photo out of a set I took recently. BUT as I and a few others alluded to quite some time ago in a thread, we think the colour cast issue is a white balance one. That the cameras are reading the white balance incorrectly when ND filters are in place. I have seen it corrected by a simple white balance adjustment in RAW conversion. The purple cast is not seen all the time, even with the Cokin filters, if the filter was the cause, it should be. We surmised that under certain light conditions the camera reads a faulty white balance and the purple cast is not caused by the filter as such, but the camera in combination with ND filters and certain light conditions.

Hi Rick,

I'm considering a 9 or 10 stop filter and though do prefer the convenience of the screw on type, may go for the Lee Big Stopper.

Thus placing the camera in a set WB mode (cloud, sunlight, tungsten etc) may remedy the issue?

Now that time has passed, how do you view the Lee Big Stopper and why did you choose it over the other higher end filters?

NikonUser
23-01-2012, 10:32pm
There is one of these available on Camera Market at the moment (not mine... I just saw this thread and remembered that I saw it)

ricktas
24-01-2012, 8:00am
Hi Rick,

I'm considering a 9 or 10 stop filter and though do prefer the convenience of the screw on type, may go for the Lee Big Stopper.

Thus placing the camera in a set WB mode (cloud, sunlight, tungsten etc) may remedy the issue?

Now that time has passed, how do you view the Lee Big Stopper and why did you choose it over the other higher end filters?

Yes re white balance. I tend to set mine for the scene (if its cloudy, I use cloudy), and then tweak it in PP if needed. I rarely see the magenta cast anyway. We did surmise at the time this was discussed that it seemed that Canon camera's were more susceptible, so maybe shooting Nikon is an advantage after all.

I really enjoy shooting with the big stopper. But I also like shooting without it too. It creates drama to a shot, with long swept clouds, and silky smooth water. Sometimes though the waves etc are what I want to get. Why I chose the Lee was that at the time it was available, and Lee have a good reputation, and that it fits in my Cokin Z-Pro holder.

silkdiver
31-01-2012, 1:50am
Maybe someone can help me out, I use the Cokin Z Pro filter holder, but I can't work out whether I need the Hitech 1.5mm or the 3mm gasket big stopper (or did I miss it when I read through the pages here) Hitech's website only tells you which size for Lee or Hitech holders.

Thanks...Jo

silkdiver
31-01-2012, 7:35am
The answer is ... 1.5mm gasket :)
for anyone else that may need to know

Xenedis
01-02-2012, 4:21pm
My Hitech ten-stop ND filter arrived today.

It's nice and dark!

Looking forward to using it this weekend.

peterb666
02-02-2012, 12:43am
My Hitech ten-stop ND filter arrived today.

It's nice and dark!

Looking forward to using it this weekend.

Congratulations. It is fun and a bit of a challenge.

Analog6
02-02-2012, 8:44am
The HiTech Pro 10-stopper comes with it's own cheat sheet that fits perfectly in the window on the front of the Lee 10-filter case.

does it fit the Lee filter holder too?

Answered my own question - see the good review (http://www.dannylintonphotography.com/nggallery/hitech-nd-pro-10-stop-review/).

Silkdiver, this answers your question too re Cokin.

Xenedis
02-02-2012, 4:55pm
Congratulations. It is fun and a bit of a challenge.

Until now I've been stacking two three-stop ND filters, so I'm not too worried. :-)


does it fit the Lee filter holder too?

It sure does.