PDA

View Full Version : The glowing filament shot



DesmondD
17-07-2010, 4:50pm
I've been playing around with the idea of the smashed light bulb shot with a glowing filament for a while and today I went in to town to get some cheap bulbs to smash and all the shop had was frosted bulbs ! What a nuisance .
So I tried it anyway with the one clear bulb I had and went through the frosted bulbs as well .

This was my 'studio' , I was surprised at how well the D40 and 35mm 1.8 lens focused in this light , I fired an SB26 at 1/4 power to the side and it triggered the one SB800 that was in SU4 mode .

http://i107.photobucket.com/albums/m300/dvdowns/high%20speed/zsmashsetup002.jpg

I had the D90 with a protective cover on it in case the bulbs had powder in them and the 18-200 lens at F11 and 2 seconds , iso 200 .
This was a test shot while it was still too light to shoot .
The filament glow was created by firing another flash with the bulb and a soldering iron in series with the circuit .

http://i107.photobucket.com/albums/m300/dvdowns/high%20speed/zsmashfrosted008.jpg

And I sort of messed up with the one and only clear bulb I had , I hit too hard and went too far into it .

http://i107.photobucket.com/albums/m300/dvdowns/high%20speed/zsmashfrosted023c.jpg

Tomorrow I may try to find some more clear bulbs but for now I have quite a few images of frosted bulbs to go through .



.

DesmondD
17-07-2010, 5:24pm
The frosted bulbs were difficult to work with , trying to see the glow and time the hit right .

http://i107.photobucket.com/albums/m300/dvdowns/high%20speed/zsmashfrosted025.jpg

I was hoping to get the crack to show the glowing filament from the side but no such luck .

http://i107.photobucket.com/albums/m300/dvdowns/high%20speed/zsmashfrosted026.jpg

http://i107.photobucket.com/albums/m300/dvdowns/high%20speed/zsmashfrosted027.jpg


.

DesmondD
17-07-2010, 5:35pm
A couple more ....

http://i107.photobucket.com/albums/m300/dvdowns/high%20speed/zsmashfrosted031.jpg

http://i107.photobucket.com/albums/m300/dvdowns/high%20speed/zsmashfrosted032.jpg


http://i107.photobucket.com/albums/m300/dvdowns/high%20speed/zsmashfrosted033.jpg


.

I @ M
17-07-2010, 6:37pm
Desmond, I really think the 3rd shot in the first series is great, a bit more glow from the filament would have worked but the detail from the flying bulb makes up for it. :th3:

DesmondD
17-07-2010, 6:45pm
Desmond, I really think the 3rd shot in the first series is great, a bit more glow from the filament would have worked but the detail from the flying bulb makes up for it. :th3:

Thanks - I need to drop the hammer rather then hit with it - it helps to bulb to bounce off the surface as well . The frosted bulbs were extremely weak and broke easily though .

DesmondD
17-07-2010, 8:46pm
Of course I had to do a few with the sword !

http://i107.photobucket.com/albums/m300/dvdowns/high%20speed/zsmashfrosted035.jpg

http://i107.photobucket.com/albums/m300/dvdowns/high%20speed/zsmashfrosted039.jpg

http://i107.photobucket.com/albums/m300/dvdowns/high%20speed/zsmashfrosted040.jpg

http://i107.photobucket.com/albums/m300/dvdowns/high%20speed/zsmashfrosted044.jpg



.

kaiser
17-07-2010, 9:15pm
Nice work mate, you're getting some great shots from this little rig :)

DesmondD
18-07-2010, 5:49am
Nice work mate, you're getting some great shots from this little rig :)

Thanks - I may have to just cough up on some of the newer clear light bulbs . Ubfortunately they are making them much smaller these days :(

milspec
18-07-2010, 12:21pm
#3 is definitely a ripper.

I hope that the 'All Steel Hammer' is being held with caution ... or at least not by you ;)

DesmondD
18-07-2010, 12:25pm
#3 is definitely a ripper.

I hope that the 'All Steel Hammer' is being held with caution ... or at least not by you ;)

It does have a rubber handle :) But it's probably only about 50 volts going through the filament .

Billnick
18-07-2010, 1:06pm
It does have a rubber handle :) But it's probably only about 50 volts going through the filament .

It may have 50v going through the circuit but if the active lead goes to the filament before the soldering iron there will be 240v on one of the filament probes. If you touch it you will get zapped. Make sure the active lead goes to the soldering iron first.

Interesting pics though.:)
Bill

DesmondD
18-07-2010, 1:35pm
It may have 50v going through the circuit but if the active lead goes to the filament before the soldering iron there will be 240v on one of the filament probes. If you touch it you will get zapped. Make sure the active lead goes to the soldering iron first.

Interesting pics though.:)
Bill

Yep , the soldering iron is first in line with the capacitor and then the bulb and then the flash tube .:)
I'm thinking about using a starter solenoid to push a spray can up against two contacts joined to the capacitor .... BOOM ! :lol::th3:

DesmondD
24-07-2010, 4:30pm
Today I bought 10 clear bulbs - I'll post some pictures after I finish cleaning up ALL THAT GLASS ON THE DARN GARAGE FLOOR !

http://i107.photobucket.com/albums/m300/dvdowns/high%20speed/zsmash2011.jpg

.

DesmondD
24-07-2010, 5:13pm
I'll admit that I cheated and used photoshop in one image :)

http://i107.photobucket.com/albums/m300/dvdowns/high%20speed/zsmash2032.jpg


.

DesmondD
24-07-2010, 5:47pm
And here are a few of the final images :

http://i107.photobucket.com/albums/m300/dvdowns/high%20speed/zsmash2020.jpg

http://i107.photobucket.com/albums/m300/dvdowns/high%20speed/zsmash2025.jpg

http://i107.photobucket.com/albums/m300/dvdowns/high%20speed/zsmash2028.jpg

http://i107.photobucket.com/albums/m300/dvdowns/high%20speed/zsmash2036.jpg




.

I @ M
24-07-2010, 5:52pm
Excellent Desmond :th3:

#3, the closeup, has the most impact (pardon the pun) as a photo but I reckon you have done a top job on all.

DesmondD
24-07-2010, 6:02pm
Excellent Desmond :th3:

#3, the closeup, has the most impact (pardon the pun) as a photo but I reckon you have done a top job on all.

Thanks - still not perfect but the last one I took when I remembered I had an axe shows promise :)

DesmondD
25-07-2010, 3:47pm
Waiting for dark really gets to me - so I suppose you will all have to put up with me posting test shots until it gets dark :)

http://i107.photobucket.com/albums/m300/dvdowns/high%20speed/zsmashsword008.jpg


practice video (http://www.youtube.com/watch?v=rX4CBOjE5Bo)




.

DesmondD
25-07-2010, 4:47pm
And I've just used up my last clear light bulbs ... for now :)

The video (http://www.youtube.com/watch?v=BgzLlkL1QAo)

http://i107.photobucket.com/albums/m300/dvdowns/high%20speed/zsmashsword012.jpg

The bulb never broke but my face is in the reflection :)

http://i107.photobucket.com/albums/m300/dvdowns/high%20speed/zsmashsword013.jpg

http://i107.photobucket.com/albums/m300/dvdowns/high%20speed/zsmashsword015.jpg

http://i107.photobucket.com/albums/m300/dvdowns/high%20speed/zsmashsword016.jpg

http://i107.photobucket.com/albums/m300/dvdowns/high%20speed/zsmashsword018.jpg

Then someone pulled up on the farm with a truck and messed my shot up !

http://i107.photobucket.com/albums/m300/dvdowns/high%20speed/zsmashsword020.jpg

http://i107.photobucket.com/albums/m300/dvdowns/high%20speed/zsmashsword022.jpg



.

I @ M
25-07-2010, 6:13pm
The last photo is an absolute gem :th3:

Mate, you are a true legend in your own life lunch time. :D

:aaa:

DesmondD
25-07-2010, 6:24pm
The last photo is an absolute gem :th3:

Mate, you are a true legend in your own life lunch time. :D

:aaa:

Thanks :) The last one always seems to be the best as I try to think of something new !